在线客服

在线客服
工作时间

周一周六 8:30-17:30

联系方式

娄经理13902200853

新闻资讯

NEWS
博客详情
当前位置: 首页> 博客详情
Nanyang creates 20 kinds of dry powder materials for 3 minutes uniform technology
所属分类:Company News
发布日期:2018-12-30
点击率:69
收藏:

1546075536272029267.jpg

(All sizes and sizes can be customized, please contact the seller for the price!)


(We are a manufacturer. Please contact us on the official website to see the information, you can give a discount!)


The trough mixer produced by our factory has exquisite structure and beautiful appearance. It is suitable for mixing and even mixing of powder or granular materials in pharmaceutical, daily chemical, food, chemical, dye, pesticide, metallurgy, ceramics and other industries. No dissolution, volatilization or deterioration of the material occurs during the mixing process.


The trough type mixing body is made of stainless steel tank, which is polished inside and outside for easy cleaning. The stirring spiral rotates, the two-way material turns to the middle, and the outer spiral pulp pushes to both sides. The two-way spiral stirring blade and the two-sided spiral slurry are combined to make the material continuously run in the tank body, and the whole seal is leak-free during the mixing process.


We dare to promise!


100L dry powder, 20 categories of materials within 5 minutes evenly!



Third, the construction description


1. Stirring reducer: The reducer series is the main transmission mechanism of the mixer. It is located on the right side of the machine. When working, the motor in the frame is driven by the chain to drive the worm and worm gear, which is driven by the speed ratio of 1:51. The agitator shaft has a sealing device at the end of the agitating shaft, and the back cap can be removed for cleaning.


2. Mixing tank: The tank is made of stainless steel, equipped with agitating slurry, and placed on the mixing and deceleration and the material reducer.


3. Rewinding reducer: The reversing reducer is used to control the positioning angle of the mixing tank. It is located on the left side of the machine. When working, the motor in the frame passes the chain drive worm. The worm wheel drives the mixing groove to rotate within a certain range of use. The material is poured out at once.


Fourth, the use of instructions and precautions


1. Before use, a dry run test should be carried out. During the test run, observe whether the operation of each component is normal, whether there is special noise, whether the temperature of the reducer rises, and if it is normal, it can be put into production.


2. Disassemble the mixing slurry: When disassembling and stirring, first remove the two ends and tighten the nut, then pull out the stirring slurry smoothly. When the mixing slurry is assembled and disassembled, it should be kept steady, and it should not be hardened and knocked to avoid bending and deformation.


3. If you need to scrape the groove wall material during operation, you should use tools. Do not use your hands to avoid accidents.


4. If the machine vibration is abnormal or there is abnormal noise during use, stop it immediately.


5. The load should not be too large, and the working current of the stirring motor is 6.8 amps as normal.


Five, machine parts lubrication


The lubrication of the reducer is oil-immersed. Before driving, the 30# oil must be injected into the left and right reduction gearboxes. The oil quantity is half of the oil mark, and the dumping support is lubricated by the oil cup, once per shift. To keep the oil clean, change the oil every six months.


Six, maintenance instructions


1. Regularly inspect the machine parts and perform 1~2 times a month to check whether the various parts of the worm gear, worm, bearing, shaft seal and so on are working normally, and find that the defects should be repaired in time.


2. When using once or stopping work, the remaining materials should be taken out and the materials left in each component should be removed. If the deactivation time is long, the machine must be wiped clean and the smooth surface of the machine is coated with anti-rust oil. The cover is good.


Seven, installation instructions


This machine is packed in the whole box. After unpacking, place it in the proper place, use it after leveling, and it is better to fix it with the foot bolts.


Eight, electrical instructions


The power of the machine is 380V AC. The mixing time is controlled by hand and self-control. When using the automatic control, the user should put the rotary button in the automatic control position and adjust the required mixing time. Even if the hand is controlled, the rotary button is placed in the manual position. Just fine. Damage to the transmission components must be checked frequently to ensure reliable operation.


We dare to promise!


100L dry powder, 20 categories of materials within 5 minutes evenly!


It can be dumped and discharged. The size of the discharge port can be customized according to the bag. The liquid nozzle can be installed above. Other requirements can be customized according to requirements.


The trough mixer produced by our factory has exquisite structure and beautiful appearance. It is suitable for mixing and even mixing of powder or granular materials in pharmaceutical, daily chemical, food, chemical, dye, pesticide, metallurgy, ceramics and other industries. No dissolution, volatilization or deterioration of the material occurs during the mixing process.


The trough type mixing body is made of stainless steel tank, which is polished inside and outside for easy cleaning. The stirring spiral rotates, the two-way material turns to the middle, and the outer spiral pulp pushes to both sides. The two-way spiral stirring blade and the two-sided spiral slurry are combined to make the material continuously run in the tank body, and the whole seal is leak-free during the mixing process.


下一页:Basic upgrade of medium and high-end machine tools